话说右摇杆完全没反应要改的都改了！...

vbccx4

我是用北通c036,在游戏里面怎么摇也没反应

郁闷啊！

求请教~~~~

ys1125

[PAD1]
Index=0                   #controller index in system game controllers list; 0 is first; -1 to ignore this pad
Left Analog X=1           #axis index; use - to invert; precede with 's' for a slider eg; s-1; 7 to disable
Left Analog Y=-2          #axis index; use - to invert; precede with 's' for a slider eg; s-1; 7 to disable
Right Analog X=3          #axis index; use - to invert; precede with 's' for a slider eg; s-1; 7 to disable
Right Analog Y=-6         #axis index; use - to invert; precede with 's' for a slider eg; s-1; 7 to disable
Left Analog X Linear=0    #-100 to +100  raise this number to increase sensitivity near center
Left Analog Y Linear=0    #-100 to +100  raise this number to increase sensitivity near center
Right Analog X Linear=0   #-100 to +100  raise this number to increase sensitivity near center
Right Analog Y Linear=0   #-100 to +100  raise this number to increase sensitivity near center
Left Analog X+ Button=0   #button id; 0 to disable
Left Analog X- Button=0   #button id; 0 to disable
Left Analog Y+ Button=0   #button id; 0 to disable
Left Analog Y- Button=0   #button id; 0 to disable
Right Analog X+ Button=0  #button id; 0 to disable
Right Analog X- Button=0  #button id; 0 to disable
Right Analog Y+ Button=0  #button id; 0 to disable
Right Analog Y- Button=0  #button id; 0 to disable
D-pad POV=1               #POV index; 0 to disable
D-pad Up=0                #button id; 0 to disable
D-pad Down=0              #button id; 0 to disable
D-pad Left=0              #button id; 0 to disable
D-pad Right=0             #button id; 0 to disable
A=2                       #button id; 0 to disable
B=3                       #button id; 0 to disable
X=4                       #button id; 0 to disable
Y=1                       #button id; 0 to disable
Left Shoulder=5           #button id; 0 to disable
Right Shoulder=6          #button id; 0 to disable
Back=9                    #button id; 0 to disable
Start=10                  #button id; 0 to disable
Left Thumb=11             #button id; 0 to disable
Right Thumb=12            #button id; 0 to disable
TriggerDeadzone=0         #use 0 to 255; default 0; add deadzone to trigger
Left Trigger=7          #button id; precede with 'a' for an axis; 's' for a slider; 'x' for a half range axis; 'h' for half slider; use '-' to invert ie. x-2;
Right Trigger=8         #button id; precede with 'a' for an axis; 's' for a slider; 'x' for a half range axis; 'h' for half slider; use '-' to invert ie. x-2;
UseForceFeedback=1        #use 0 to 1; default 0
SwapMotor=0               #use 0 to 1; default 0
ForcePercent=100          #use 0 to 100; default 100
ControllerType=1          #GAMEPAD 1; WHEEL 2; STICK 3; FLIGHT_SICK 4; DANCE_PAD 5; GUITAR 6; DRUM_KIT 8;   //WILDS
AxisToDPad=0              #Use Axis to control DPad (0 disabled, 1 enabled)                                 //WILDS
AxisToDPadDeadZone=256    #Dead zone for Axis                                                               //WILDS
AxisToDPadOffset=0        #                                                                                 //WILDS
POVXReverse=0             #Reverse POV Up/Down
POVYReverse=0             #Reverse POV Left/Right
你说的太简短啦..我都不知怎么帮你...我把我整个x360ce.ini那个里面的全部复制给你了...你试一下..我这么用一点问题都无

514273668

两个摇杆中间有个按键  叫ANALOG 你看它下面的灯亮了没  没的话 按下按键

metyph

话说用那个什么Xinput 设置下就好了~我用手柄玩都用这个设置~摇杆也可用
关于这个Xinput，网上很多的~搜一下就可以 了~论坛里也有~搜搜一下对身体健康有好处